Sales Office: +44 (0)1777 871310 Direct Contact: +44 (0)7803 591756 Manufacturing: +44 (0)1673 866200 R&D: +44 (0)1673 265055

QUALITY STANDARDS

TECHNICAL STANDARDS AND SUPPLEMENTARY DOCUMENTS. Unless otherwise stated, the following documents shall be applied when executing these specifications: Sniper Extreme standards and drawings – various calibers and types.

 

BS6001 – 0:2006/ ISO-2859-10:2006 – Part 0 – Introduction to BS6001 (ISO2858) series of standards for sampling for inspection by attributes.

 

BS6001 – 1:1999/ ISO-2859-1:1999 – Part 1 – Sampling schemes indexed by Acceptance Quality Limit (AQL) for lot by lot inspection.

 

ISO 3951-1:2013 – Sampling procedures for inspection by variables. Part 1: Specification for simple sampling plans indexed by Acceptance Quality Limit (AQL) for lot by lot inspection for a single quality characteristic and a single AQL.

 

ANSI/ASQ Z14 – 2003 – Sampling plans and procedures for inspection by attributes.

 

MIL-STD-636 – Visual inspection standards of Small Arms Ammunition through to .50 caliber.

 

MIL-STD-1168A – Ammunition Lot Numbering.

 

MIL-A-48078 (AR) – Ammunition, Standard Quality Assurance Provisions.

 

CIP 2011 – Commission Internationale Permanente. European standard for small arms ammunition.

 

NATO PFP (NAAG-LCG/1-SG/1)WP(2010)0002 – Multi Caliber MOPI (WHERE APPLICABLE).

 

ANSI/SAAMI Z-22994 – 1992 – Voluntary industry performance standards for pressure and velocity of Centrefire rifles and sporting ammunition for the use of commercial manufacturers.

1.1 – Order of Priority

 

It is recognised that different standards exist for different countries and clients, much of this will be accomodated in subsequent technical acceptance plans. For the purpose of this Technical Qualification Acceptance Plan, taking into account all the supplementary documents mentioned previously, priority shall be given to the following standards;

 

Sniper Extreme Standards and drawings various calibers and types.

 

BS6001-0:2006/ ISO-2859-10:2006 – Part 0 – Introduction to BS6001 (ISO2858) series of standards for sampling inspection by attributes.

 

BS6001-1:1999/ ISO-2859-1:1999 – Part 1 – Sampling schemes indexed by acceptance quality limit (AQL) for lot by lot inspection.

 

ANSI/ASQ Z14 – 2003 – Sampling plans and procedures for inspection by attributes.

 

CIP 2011 – Commission Internationale Permanente. European standard for small arms ammunition.

 

ANSI/SAAMI Z-22994 – 1992 – Voluntary industry performance standards for pressure and velocity of centrefire rifles sporting ammunition for the use of commercial manufacturers.

 

NATO PFP (NAAG-LCG/1-SG/1)WP(2010)0002 – Multi caliber (WHERE APPLICABLE).

 

MIL-STD-636 – For visual inspection of the cartridges.

 

MIL-STD-1168A – For the numbering of the lots.

CONTACT

Sales Office
EPA Manufacturing Ltd
Nottinghamshire
NG22 0LJ
t: +44 (0)1777 871 310
e: bm@epgroupltd.com

Manufacturing
Unit 154
Faldingworth Base
Spridlington Road
Lincolnshire, LN8 3SQ
t: +44 (0)1673 866200

Manufacturing
Station Yard
Station Road
Mildenhall
Suffolk
IP28 7DT

Research &
Development

Building 1
Faldingworth Base
Spridlington Road
Lincolnshire LN8 3SQ

EPA Manufacturing Ltd

ISO 9001:2015
Certificate Number 10414